#1
|
|||
|
|||
Motor does'nt work forward???
I putt a new motor on my car and after that my motor never go forward..only backward....my steering and my light work.....i take another motor with the same result.......where is the trouble...i didn't make contact with my antenna on my wiring or another source of power.
|
#2
|
|||
|
|||
lol
did you clean yo car? or is it new ?well clean it or make the axle thing in the middlebe inside the gear dat u change ed in the back and spin tire till it is in
__________________
Znd racing team got rice? Any one here......hello?! |
#3
|
||||
|
||||
Re: Motor does'nt work forward???
Quote:
Now turn on your xmod like your gonna drive it and throttle it backwards and forwards. Does the motor spin both ways? If the answer is yes, you have a mechanical problem with your drivetrain. If the answer is no, you have an electronics problem. |
#4
|
|||
|
|||
Re: Motor does'nt work forward???
Quote:
|
#5
|
||||
|
||||
Re: Motor does'nt work forward???
Quote:
this happened to me...it's the forward FET. one of the legs fried...either replace the main board or pay someone to stack new FETs. |
#6
|
|||
|
|||
Re: Motor does'nt work forward???
Quote:
|
#7
|
||||
|
||||
As for this
If you cannot or are unable to resolder a new set of FETs, then reverse the switch on your controller to press for forward...or if that does not work, reverse the leads on the motor.
In any event, I suggest getting both FETs in new with the higher capacity ones.
__________________
I love things with gears and wheels... |
#10
|
|||
|
|||
ok thanks.......wher i can find a new board to replace my fried board...i don't want to resolder the fet.....and with my new board can i have the same trouble with my fet or it's a badluck???
|
#11
|
||||
|
||||
Radio Shack and try ordering part no. 12414207. I believe that is the main board. that should take care of your problem. remember to clean between the chassis and the main board...running it inside or out you run the chance of picking upi a small sliver of metal (which probably happened 2 us) and shorting a FET. when you get the new board cover the FETs with s thin coat of clear silicone sealent. that should keep dirt and moisture away.
|
#12
|
|||
|
|||
Ok thanks a lot...but after i install my new board can i putt my lithium on it or i have a chance of break them again??And with my li-ion i broke 2 motor after overheating,with my new board i have a chance of break them again!!!!!
|
#13
|
|||
|
|||
the lithiums didnt cause your problem, you had a defective fet to begin with. i have 3 xmods with lithiums, they all work fine. actually i wish i had a dyno to put them on. they go pretty **** fast. i race them against miniz's at and they pull their wieght.
|
#14
|
|||
|
|||
Quote:
|
#16
|
|||
|
|||
how much is the main board????
__________________
http://img.photobucket.com/albums/v2...3/warlock2.jpg |
#18
|
|||
|
|||
I receive my new elctronic kit from ebay.....i putt it in my car and all work very well.....few day after my car does'nt go forward...another fet is fried?????Where is the problem with my car and my li-ion cell????
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
pUT LITHIUMS IN DOESN'T WORK! | SwedishRacer | XMOD Modification | 4 | 09-04-2004 09:22 AM |
my eclipse....its a work in progress | bigsho | XMOD Appearance | 3 | 08-23-2004 08:22 PM |
does testors work? | skylinebob14 | XMOD Modification | 2 | 08-06-2004 12:42 PM |