Bananabrain
08-05-2009, 05:28 PM
Difficulty around 4/10
Time 5-10 Mins per tire, 25-40 Mins for total Process
Ok, well ive seen how other people have put oversized tires on the truck or hummer xmods. So i dug around in my room and found some huge tires, and wanted to attatch them to my mudder, so i figured out the easiest way i could think of to do it and it be reversible to.
This is my first Tut so if there are any mistakes, let me know.
Ok,
Step #1
You will need the following items:
An xmod truck chassi (with wide wheel upgrade, optional on that it just works better),
Your Oversized tires,
Some Model glue (plastic Cement) or Super glue (but model glue removes easier,
A round File,
Stock hummer, f-150, or Nissan Titan, Rims & Tires,
Your tool to remove wheel nuts (the one shown in pick is the best to use),
X-acto Knife (optional),
And a soldering iron/gun, (not pictured)
And yes im missing a tire.
Note this will only work with rims and tires like the ones im using, This may also be similar to other tires but the steps may be a bit different.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires001.jpg
Step #2
Ok, first thing you do is after your soldering Iron/gun has heated up, put it in the hole on the rim and push it through, and move it around a little to make the hole bigger, so the round file can move around in it.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires002.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires003.jpg
Step #3
Then take your round file and start filing out the center hole, Use the X-acto Knife to cut off the plastic hanging off of the rim when your done filing.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires004.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires005.jpg
Then once you have done that, it should look like the pick below,
After:
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires006.jpg
Before:
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires007.jpg
There should now be enough room to fit the Tool through the hole and have a little wiggle room.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires008.jpg
Step #4
Then take some Model Glue and/or Super Glue, and put it on the tread of the xmod tire.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires009.jpg
Then once you have done that put it on to of the tire and make sure you have it on straight,
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires010.jpg
Then you push it in the center till it wont go down anymore.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires011.jpg
Repeat steps 2-4 for the other three Tires
Here is the finished look,
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires012.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires013.jpg
This is something similar:
Ok, i did something similar to this Tut so here it is below, I cut and sanded out the center of the wheel then put a off road upgrade rim in the back of it and painted it Flat Black.
http://i362.photobucket.com/albums/oo63/bananabrain_07/008-2.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/009-2.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/007-2.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/006-3.jpg
Time 5-10 Mins per tire, 25-40 Mins for total Process
Ok, well ive seen how other people have put oversized tires on the truck or hummer xmods. So i dug around in my room and found some huge tires, and wanted to attatch them to my mudder, so i figured out the easiest way i could think of to do it and it be reversible to.
This is my first Tut so if there are any mistakes, let me know.
Ok,
Step #1
You will need the following items:
An xmod truck chassi (with wide wheel upgrade, optional on that it just works better),
Your Oversized tires,
Some Model glue (plastic Cement) or Super glue (but model glue removes easier,
A round File,
Stock hummer, f-150, or Nissan Titan, Rims & Tires,
Your tool to remove wheel nuts (the one shown in pick is the best to use),
X-acto Knife (optional),
And a soldering iron/gun, (not pictured)
And yes im missing a tire.
Note this will only work with rims and tires like the ones im using, This may also be similar to other tires but the steps may be a bit different.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires001.jpg
Step #2
Ok, first thing you do is after your soldering Iron/gun has heated up, put it in the hole on the rim and push it through, and move it around a little to make the hole bigger, so the round file can move around in it.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires002.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires003.jpg
Step #3
Then take your round file and start filing out the center hole, Use the X-acto Knife to cut off the plastic hanging off of the rim when your done filing.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires004.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires005.jpg
Then once you have done that, it should look like the pick below,
After:
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires006.jpg
Before:
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires007.jpg
There should now be enough room to fit the Tool through the hole and have a little wiggle room.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires008.jpg
Step #4
Then take some Model Glue and/or Super Glue, and put it on the tread of the xmod tire.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires009.jpg
Then once you have done that put it on to of the tire and make sure you have it on straight,
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires010.jpg
Then you push it in the center till it wont go down anymore.
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires011.jpg
Repeat steps 2-4 for the other three Tires
Here is the finished look,
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires012.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/hummertires013.jpg
This is something similar:
Ok, i did something similar to this Tut so here it is below, I cut and sanded out the center of the wheel then put a off road upgrade rim in the back of it and painted it Flat Black.
http://i362.photobucket.com/albums/oo63/bananabrain_07/008-2.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/009-2.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/007-2.jpg
http://i362.photobucket.com/albums/oo63/bananabrain_07/006-3.jpg