|
|
|
#1
05-12-2007, 11:17 PM
|
||||
|
||||
Micro-t
Well i just had my birthday party yesterday and i have $170 and still havent recieved money from a couple of other relatives and since i have all this money i have been looking into the micro-t. I like xmods but they are kinda unreliable and i want to get into hobbygrade. I have heard some good stuff about the micro-t and i was just wondering how it is stock cuz i wont be puttin upgrades into it for ahwile. I would like to know about how fast it is stock,Can it pull wheelies from a standstill stock,How does it handle stock, and how durable is it.Thanks in advance for any information.
__________________
My whips: Hummer: all rs upgrades, 6cell and custom superswampers(off roader) G35: currently being repaired(dead) Mustang: all rs upgrades,blue gpm knuckles, 39 turn motor (circuit/top speed) Scion TC: all rs upgrades, drift kit and 6 cell (drifter) blue F-150 body (offroad bodykit) G35 body top targa top and some custom bodywork 
|
|
#2
05-13-2007, 12:59 AM
|
|||
|
|||
|
i kno there fast and can do wheelies
|
|
#3
05-13-2007, 12:59 PM
|
||||
|
||||
|
Quote:
2.) It pulls wheelies until the battery is dead, which is ussually a good 20 minutes. 3.) It handles great. Doesn't Roll, turns tight. The diff is a bit tight from the begining, but after a few runs, it loosens up giving you a good turning radius. 4.) It's durable. Really good. Metal Drivetrain holds up. I've jumped it off 1foot high ramps, holds fine. It bottoms out and smacks the bottom sometimes, but nothing bad... You can use the spring set for the EvoT for springs on the Micro-T. It's only $80, so it won't use all your money either.
__________________
After a thousand years of oppression,
Let the berserks rise again, Let the world hear these words once more: "Save us, oh lord, from the wrath of the Norsemen"
|
|
#4
05-13-2007, 05:24 PM
|
||||
|
||||
|
alright thanks alot Sweed im trying to get my mom to order one right now.
__________________
My whips: Hummer: all rs upgrades, 6cell and custom superswampers(off roader) G35: currently being repaired(dead) Mustang: all rs upgrades,blue gpm knuckles, 39 turn motor (circuit/top speed) Scion TC: all rs upgrades, drift kit and 6 cell (drifter) blue F-150 body (offroad bodykit) G35 body top targa top and some custom bodywork
|
|
#5
05-13-2007, 06:01 PM
|
||||
|
||||
|
I have been extensively researching micro-ts and from what I have read they're very durable except for the tie rods which break a lot. luckily you can fabricate virtually indestructible tie rods using zip-ties. I am going to buy a micro-t as soon as my xmods stuff sells on ebay. I can't wait!
__________________
It's usually easier to ask for forgiveness than permission.
|
|
#6
05-13-2007, 08:44 PM
|
||||
|
||||
|
All the Micro-T Research you'll ever need can be found below:
www.ripper7racing.com
__________________
After a thousand years of oppression,
Let the berserks rise again, Let the world hear these words once more: "Save us, oh lord, from the wrath of the Norsemen"
|
|
#7
05-14-2007, 04:33 PM
|
||||
|
||||
|
yea i have been looking on r7r for 2 days now and i ordered a blue micro t yesterday from atomicmods. I ordered it from them because i live in maryland and i here how fast they ship so hopefull it'll be hear by wednesday or if im lucky it'll be here tomorrow. Also Sweed is there any upgrades that you recommend i get. I was thinking about bearings and i was wwondering where they go?
__________________
My whips: Hummer: all rs upgrades, 6cell and custom superswampers(off roader) G35: currently being repaired(dead) Mustang: all rs upgrades,blue gpm knuckles, 39 turn motor (circuit/top speed) Scion TC: all rs upgrades, drift kit and 6 cell (drifter) blue F-150 body (offroad bodykit) G35 body top targa top and some custom bodywork
|
|
#8
05-14-2007, 05:54 PM
|
||||
|
||||
|
I got my bearings from the my LHS, Losi-Factory Bearings. Spin forever...
I recomend that you get lock-nut type axels or pick up plenty of e-clips, when they pop off, they're gone... Just don't get the axels from Atomic Mods, expesnive... Oh, and the Atomic BB (Brass Bushing, not bearing) is a good motor too.
__________________
After a thousand years of oppression,
Let the berserks rise again, Let the world hear these words once more: "Save us, oh lord, from the wrath of the Norsemen"
|
|
#10
05-14-2007, 07:53 PM
|
|||
|
|||
|
let me kno how it is once u get it i want to get one but i wasnt sure if i should
|
|
#11
05-14-2007, 08:08 PM
|
|||
|
|||
|
sweed your e clips pop off...mine have yet to do that. anywayz i recomend every aluminum upgrade you can get your hands on after i did this mine is indestructible. tell me how you like the micro-t...i absolutely adore it. way better than xmods, but not better than a nitro, although the price definetly is
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
