XXX: Modders Convention

[reaper]

in that case use an evo drive cup in the same way , then on the end of the drive shaft that goes to the front diff drill it and add a pin to make a dogbone

add or remove the pin for rwd or 4wd

[TripleXmodder(akaXXX)]

Originally Posted by mycrors4

i have the dremel but i lack patience.. especially for long periods of time.. and i dont have a very steady hand.. i think the extra $10 to have it CNCed is worth it, because a) it wont have any mistakes(unless i do some calculations wrong).. and it will be well cleaner that what i could do

Where the **** are you getting CNC for ONLY extra $10.00

[mycrors4]

Originally Posted by TripleXmodder(akaXXX)

Where the **** are you getting CNC for ONLY extra $10.00

i meant $10/hr lol
but i found a aluminum cutting factory i just send them the CAD files.. it shouldnt be over $100 cause its not laser cut
http://www.thunderbirdwaterjet.com/index.html

in Los Angeles, Downtown.. anything is possible lol if i try hard enough i can find $5/30 mins CNC places.. but they do crappy jobs

[reaper]

send me the material i will do it for free man dont pay $100

[mycrors4]

Originally Posted by reaper

send me the material i will do it for free man dont pay $100

but see i wont need to CNC.. they just need files

[reaper]

dude you make no sence , you ask questions and when you get replys you change what you are asking ???????

if its just going to be filed do it yourself dont pay $100 for it , if you want it cutting by machine i will do it for free

[mycrors4]

Originally Posted by reaper

dude you make no sence , you ask questions and when you get replys you change what you are asking ???????

if its just going to be filed do it yourself dont pay $100 for it , if you want it cutting by machine i will do it for free

im confused.. i never asked anything

[reaper]

this whole thread is a Q&A

you asked about shaftless rwd ......then changed you question to selectable
awd-rwd
your posts about the chassis i would take as questions on ideas of how to do it
if not then build the chassis and post the results

[mycrors4]

Originally Posted by reaper

this whole thread is a Q&A

you asked about shaftless rwd ......then changed you question to selectable
awd-rwd
your posts about the chassis i would take as questions on ideas of how to do it
if not then build the chassis and post the results

oh about that.. i posted the chassis as a small teaser to occupy people

the shaftless rwd, i see how u can do that, but i think i have some other way to do it i like keeping secrets

[reaper]

then make a project thread

this one is for sharing ideas and culminating solutions

[TripleXmodder(akaXXX)]

LOL, ahh are first confrontation on the thread. .... anyway, you can CNC reaper? what material and capabilities, although I wouldn't expect it to be FREE.

[mycrors4]

ohh well my original thought was to see ur thoughts/ideas/reactions, i wanna make this in a way that everyone likes, not a way just 1 or 2 people are gonna like

[XMDrifter]

use an evo rear and hybrid it to a gen-1 front. then line it up and make a chassis plate that will allow secure mounting of both front and rear. how about that? that's close to shaftless gen1 rwd. if not, then it may be neccesary to have a bevel gear that has a short axke stub in it with a hole drilled into it somewhere so you can use a set-screw to hold it onto the shaft?

[texan_idiot25]

Meh, I'd have to reckon the Evo gear box is a very innefficient gear box. Lots of gears. Just have the bevel gear on a very short cut drive shaft. Two bearings back to back keep it level. Put front suspension on the back with links to keep the knuckles straight and you have shaftless, and no sing arm IRS.

[lol]

Originally Posted by XMDrifter

use an evo rear and hybrid it to a gen-1 front. then line it up and make a chassis plate that will allow secure mounting of both front and rear. how about that? that's close to shaftless gen1 rwd. if not, then it may be neccesary to have a bevel gear that has a short axke stub in it with a hole drilled into it somewhere so you can use a set-screw to hold it onto the shaft?

Done.

[mycrors4]

Originally Posted by lol

Done.

he means make a new chassis to accommodate that but urs works too lol

[blazer94]

what i would like to see is hydrolics. for people who like lowriders. anybody ever have one of those jesse james car? i think it would be hard to make the hydros small but like in the jesse james car they used motors to move the wheels up and down.

[TripleXmodder(akaXXX)]

Originally Posted by blazer94

what i would like to see is hydrolics. for people who like lowriders. anybody ever have one of those jesse james car? i think it would be hard to make the hydros small but like in the jesse james car they used motors to move the wheels up and down.

Go back 7 pages or so..

[reaper]

Originally Posted by TripleXmodder(akaXXX)

LOL, ahh are first confrontation on the thread. .... anyway, you can CNC reaper? what material and capabilities, although I wouldn't expect it to be FREE.

lol not a confrontation , i just dont see the point in wasting space in this thread lets put it to good use

i can CNC carbonfibre (just flat sheet ) but alloy or any other metal for that matter i can cut and form im a fabricator by trade

couple of ideas iv had
1 for you evo-ma010 conversion have you had a word with xmodcanuck he has a 3 axis router that woud be cabbable of making the parts in one piece (not 2 glued together)
2 something iv thought about for a wile but never tryed , an 8 pin board mount IC socket in place of the FETs
then changing fets is just plug and play you could even have a stack built ready to just drop in or an adapter for a turbo
fabcy a go at that ?

[tayyab]

wow...man that idea itself is ingenious... that product production=instant millionares....

Later, T.I.M