Project: Widebody tC
Well, I've been working on this for a few months... Mostly just planning. In the last few weeks, I've been trying to add putty to make the body look lower. It's not really going to be an extreme widebody, but kinda sorta.
Pix: http://img17.imageshack.us/img17/3020/img5372.jpg Still working on the front end: http://img17.imageshack.us/img17/7955/img5373x.jpg This side needs more putty and needs to be sanded down: http://img17.imageshack.us/img17/8012/img5374k.jpg This needs more putty and some more sanding: http://img17.imageshack.us/img17/7513/img5375.jpg The rear is almost done, still needs some more details. http://img17.imageshack.us/img17/928/img5376u.jpg Little problems on the edges, needs some putty work. http://img17.imageshack.us/img17/2909/img5377x.jpg http://img17.imageshack.us/img17/665/img5378s.jpg |
i think you should go for a more sculpted and realistic bodykit. the door lines seem too low and the thing looks to be a bit slab-sided.
but that's smooth work you have, and the sharp corners are nice. the rear doesn't seem to need to be that low...it can probably do well with a sculpted diffuser and the sides with some kind of character lines to git it the depth it needs |
I'm going to try for this sort of look:
http://www.tunerzine.com/articles/266/images/14.jpg http://www.tunerzine.com/articles/266/images/11.jpg http://www.tunerzine.com/articles/266/images/12.jpg I'll change some of it, but quite a few of the elements will stay. |
well, that's a lot more curvy than the one you have right now. i think that look probably should be acheived by lowering the car body, then doing the modifications
|
Yeah... I did lower the body by 1-2 mm, and right now i'm working on puttying the body to make it look lower because simply lowering the body itself won't get rid of the tank like stock look.
|
*Double post... hehehe*
Ok... Time for a minor update. Front is still undone XD http://img21.imageshack.us/img21/8355/img5422dnd.jpg I got bored and wrote stuff on the masking tape :D http://img21.imageshack.us/img21/7614/img5428.jpg As you can see, the spoiler mount holes and where the plastic injection thingy have been filled in. Yup, it's going to be spoilerless. http://img21.imageshack.us/img21/8629/img5427.jpg The rear is being reshaped to be more accurate. Also, the little thingy on the bottom was taken off. I'm going to add some fin thingys and use .1 instead of .3 styrene: http://img21.imageshack.us/img21/3310/img5426n.jpg Rear wheel arches have been puttyed to be more parallel to the ground (it's going to do something later...) http://img21.imageshack.us/img21/5972/img5425m.jpg The front wheel wells have been puttied to be smaller so they'd look more natural: http://img21.imageshack.us/img21/9417/img5423.jpg This arch was a *****. The stupid putty didn't set as well as I thought. So I essentially destroyed it. I'm going to redo them later. http://img21.imageshack.us/img21/2381/img5424q.jpg Well that's it. C&C :D |
get rid of the side slab. you need the normal sized doors. your doors are too tall
|
Since its summer vacation, started to putty again :D
Essentially, I started to throw on a bunch of putty for the front wheel wells and the side skirts so I could remold the wheel wells and make the side skirts parallel to the ground again. Also added putty on the bottom so I could recreate the door lines. http://img5.imageshack.us/img5/2807/img7633t.jpg http://img294.imageshack.us/img294/1783/img7635z.jpg http://img30.imageshack.us/img30/4784/img7636h.jpg http://img103.imageshack.us/img103/8686/img7634.jpg I'm going to have a lot of sanding to do for the future :'( |
i have a feeling this will turn out good, i was keeping up with this but though you killed it off. glad its back.
|
yea i agree with deckerz, im positive itll turn out good in the end.. and if i dont say so myself, that little tunerzine.com scion is pretty slick car
|
Quote:
|
good good, i take it when you put your putty on you put it on in sausages?
im really feelin what you did with the wheel arches (making them smaller), makes the car look more real, gotta say your talented making a body kit with putty and it looks good, better then good, amazing, better then anything i could do with putty. |
Quote:
I usually put it on in sausages unless if there is something needed on a flat surface (I usually just smear it on XD) |
Did some more body work at one in the morning :D
http://img195.imageshack.us/img195/9788/img7644e.jpg On this side, there was some softish putty that wasn't mixed very well, so I got rid of it and smushed some more putty on that side. http://img189.imageshack.us/img189/139/img7646x.jpg Detail work and getting rid of some body lines: http://img189.imageshack.us/img189/4153/img7647o.jpg Fixing some minor errors: http://img38.imageshack.us/img38/1347/img7648c.jpg The holes weren't sanded down perfectly smooth and flat, so added some more putty there: http://img194.imageshack.us/img194/7877/img7650f.jpg And I had some extra putty left over, so I made a smiley face :) http://img30.imageshack.us/img30/4211/img7651s.jpg Now I have a lot of sanding to do :'( |
*Ahh... A triple post >.<*
After some more late night sanding, I've gotten some of the thick putty sanded away. Odd magazine ad fun :D http://img193.imageshack.us/img193/6436/img7669d.jpg The right wheel well is pretty much finished. There's enough room for the wheel to move around when turning so I'm satisfied with it. http://img118.imageshack.us/img118/8059/img7659.jpg The left wheel well still needs work done: http://img199.imageshack.us/img199/7931/img7658k.jpg I managed to sand down and smooth out some of the body lines: http://img161.imageshack.us/img161/894/img7666.jpg http://img35.imageshack.us/img35/1862/img7668o.jpg I managed to sand down the bottom really flat since I rolled the car on some sand paper XD http://img12.imageshack.us/img12/9840/img7665m.jpg I'm pretty satisfied with the right side. With the 1000 grit sand paper, it's pretty smooth. But the places where slapped the putty on it's not exactly done X( http://img18.imageshack.us/img18/5590/img7663y.jpg The left side still needs lots of work. http://img88.imageshack.us/img88/554/img7664.jpg That's it n_n C&C's please |
lol its coming pretty good, but why did you even get rid of the body lines? it looks wierd without it. like riced.
|
man this is the first time ive seen this thread, ill have to show it to cynce, she is a really good friend of mine.
(the chick that owns that scion your modeling off of) |
Quote:
I'm getting rid of most of the body lines, but I'll be etching the door panels and other random bits back in. Quote:
|
With around 3 hours of work (the styrene was a ***** trying to reshape, but I gave up so that solved that problem :D), I managed to rough shape the front fenders. This is the only major difference between the 1:1 car.
http://img41.imageshack.us/img41/9753/img7677j.jpg I put the wheels the other way to see how it was like (not bad, not bad ;) ). I'll probably start working on some widebody wheels soon. Here's the right fender... http://img33.imageshack.us/img33/4342/img7678g.jpg And the left fender... http://img19.imageshack.us/img19/5414/img7679j.jpg And now the new paint scheme... http://img17.imageshack.us/img17/9748/img7680l.jpg Sharpie! :D Naww, it's just to see what it looks like when the styrene and putty are all one color so I can shape the fenders better. |
Small update:
Added/ sanded some putty so the front wheel wells would be smoother with the front end (and be more accurate to the 1:1 model) http://img291.imageshack.us/img291/4140/img7681.jpg http://img33.imageshack.us/img33/9350/img7685.jpg And a photo of how far out the front wheel wells come out to the mirror. http://img40.imageshack.us/img40/2129/img7684z.jpg |
All times are GMT -4. The time now is 11:44 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.