XmodSource.com

XmodSource.com (http://www.xmodsource.com/forum/index.php)
-   XMOD Chassis/Suspension Tutorials (http://www.xmodsource.com/forum/forumdisplay.php?f=46)
-   -   Tutorial: How To Make Custom Drift Tires (http://www.xmodsource.com/forum/showthread.php?t=16724)

tayyab 05-12-2009 01:12 PM

Tutorial: How To Make Custom Drift Tires
 
This tut follows how to make your own custom drift tires.

Difficulty: 5/10

Tools/Things you will need:

*Rims of you Choice
*3/4 inch PVC pipe
*Hobby knife
*Low grit sanding paper
*Dremel with these bits:
http://i181.photobucket.com/albums/x...4/CIMG4380.jpg
http://i181.photobucket.com/albums/x...4/CIMG4522.jpg

http://i181.photobucket.com/albums/x...4/CIMG4379.jpg

Step 1:

Grab your rim and get rid of the ridge on the rim. The little part the goes all round the outside of the rim in the middle.
http://i181.photobucket.com/albums/x...4/CIMG4508.jpg
This can be removed in many ways, you can use a dremel, hobby knife, sandpaper etc.

Make sure the rim is absolutely smooth before moving on to the next step.
http://i181.photobucket.com/albums/x...4/CIMG4511.jpg
http://i181.photobucket.com/albums/x...4/CIMG4510.jpg

Comparison:
http://i181.photobucket.com/albums/x...4/CIMG4512.jpg

Step 2

Make sure that the end of the pipe is absolutely flat and straight, it should not be cut even 1mm left or right, this will greatly effect the finished product

Step 3:

Grab you PVC pipe
http://i181.photobucket.com/albums/x...4/CIMG4383.jpg

Now we have to reduce the thickness of the pipe using the dremel.

Use this bit:
http://i181.photobucket.com/albums/x...4/CIMG4380.jpg

Now you must move the dremel around the inside of the pipe.
Since there are many confusions when doing this i made a video:
http://i181.photobucket.com/albums/x...h_CIMG4515.jpg

Use very little pressure.

Step 4

Do this until the pipe gets hot, quickly check if you can get the rim in there like this:

http://i181.photobucket.com/albums/x...4/CIMG4516.jpg
http://i181.photobucket.com/albums/x...4/CIMG4517.jpg
http://i181.photobucket.com/albums/x...4/CIMG4518.jpg

Jam it in there nicely.

Step 5:

Put the pipe in this position:
http://i181.photobucket.com/albums/x...4/CIMG4519.jpg

Now keep whacking the pipe from the top
Or
Keep hitting the pipe on a har surface until it's in there like this:
http://i181.photobucket.com/albums/x...4/CIMG4521.jpg

WARNING!: Make sure that the rim goes in straight, it should be flush with the pipe!

You might notice that the pipe is a little stretched, this is ok.

Step 6:


Now grab the round cutting wheel and cut through the pipe about 1-2 inches away from the rim:
http://i181.photobucket.com/albums/x...4/CIMG4523.jpg

Step 6:

After the last step you should have something like this:
http://i181.photobucket.com/albums/x...4/CIMG4524.jpg

Now cut the extra pipe until it is flush with the rim:
http://i181.photobucket.com/albums/x...4/CIMG4526.jpg
http://i181.photobucket.com/albums/x...4/CIMG4525.jpg

Thats it ur done! now do this to the rest of the rims.

NOTE:

*If you think the tire does not have enough "beef" you can go buy a pipe joint, the thing to join two pipes together, apply the same process to that pipe and you will have a little thicker tire.

*You can paint it black before doing this process if you want it to look more like a real tire.

*One thing you must do if you use these tires:
http://i181.photobucket.com/albums/x...4/CIMG4494.jpg
Remove the large steering screws and swap them with the shorter ones, because now we have lower clearance so they hit the ground.

*Your clearance will reduce a lot so you may want to add the raising suspension arms for clearance.

Ok here is the best part, since these tires do not come off you can just slap the other tires over them, the larger diameter makes them stretch so they fit tightly:

http://i181.photobucket.com/albums/x...4/CIMG4498.jpg
http://i181.photobucket.com/albums/x...4/CIMG4497.jpg
http://i181.photobucket.com/albums/x...4/CIMG4501.jpg
http://i181.photobucket.com/albums/x...4/CIMG4504.jpg


And if you want a drag look, the slammed tires go perfectly over the car tire:
http://i181.photobucket.com/albums/x...4/CIMG4530.jpg
http://i181.photobucket.com/albums/x...4/CIMG4529.jpg
http://i181.photobucket.com/albums/x...4/CIMG4527.jpg

Ok, so what do you guys think?

Later, T.I.M

winner 05-12-2009 02:43 PM

nice tut, very useful a++++++

merc3des 05-12-2009 06:14 PM

Seen this before, but the pictures really help :)

Great tutorial, and its great for people who want to drift.

Maybe add if you cut slits, or drill holes it can add a little extra grip for higher speeds ;)

tayyab 05-29-2009 03:49 AM

Thanks guys. Yeah, I have an idea on the hole thingy. Like fill it in with hot glue. That would be perfect. :nod:

Will post it after my exams, 5th June.

Later, T.I.M

TripleXmodder(akaXXX) 05-29-2009 12:01 PM

I love a well photographed and put together Tut!!! Great job.

tayyab 06-17-2009 08:42 AM

Thanks.

Later, T.I.M


All times are GMT -4. The time now is 03:58 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.