XmodSource.com

XmodSource.com (http://www.xmodsource.com/forum/index.php)
-   The XMS Repair and Modification Manual (http://www.xmodsource.com/forum/forumdisplay.php?f=43)
-   -   Car keeps glitching. (http://www.xmodsource.com/forum/showthread.php?t=17649)

Michael Long 09-05-2009 07:49 PM

Car keeps glitching.
 
I have a Transformer car Bumblebee and it keeps driving then stops drives then stops and it's range is less than 1cm from controller antenna to car antenna. I am using the right crystals (checked many times) and my batteries are fully charged(Tried 2 sets of fully charged batteries). And I've seen the tutorial made about inductors. I don't think it is the inductors, this happened when I first got the car and it fixed itself automatically(I threw the car up in the air out of anger and it landed and worked), now I try driving the car again after and I haven't driving this car for more than a year because of boredom. Anyone know what is wrong? My Hummer, Ford, and Nissan work fine with the same controller and the number 5 crystal. Plus my friend had a problem with his Barricade(It did not drive at all) and he returned it for a new one.

bigez 09-05-2009 08:10 PM

try screwing the antenna screw in till it is tight that worked for me

Michael Long 09-05-2009 08:38 PM

Already tried that, first it was the motor, it needed to be screwed in tighter, which I did, then I tried screwing in the antenna. Now the car drives for 2 seconds then stops for a second and drives again for 2 seconds then repeats. I don't get it. I really want to try driving the car chassis and not the trucks for once and I can't buy another xmod yet.

bigez 09-05-2009 08:40 PM

it may just be your board have you ever touched the antennas togeather

Michael Long 09-05-2009 10:43 PM

Yes, I do that a lot with cars, the controller and car antennas. It doesn't seem to harm my 3 other xmods, but they are trucks, or the 60 other 1:16 scale RC's I had in the past. Is that a problem though?


BTW, what would be the risk of taking out a board from a truck xmod and putting it in the car xmod chassis? I've never done it before and can't afford to solder cause I only have a Cold Heat solder which doesn't work as good. I got 1 truck also which needs a gear in the back that goes on top of the rear gear diff, but I can't find a replacement part. So maybe I can use that truck's board.

bigez 09-05-2009 10:59 PM

yes that is what fried the range and make it glitch so stop doing that

the evo and evo truck boards are all the same but in order to change the board out you will needa better soldering iron if you go to radio shack you can get a good one for about 10 bucks and pick up some solder to


hope that helps

dontspamme 09-05-2009 11:04 PM

When you do the swap, be sure to get a picture of where all the wires go, especially the servo wires. Good luck with your swap.

Michael Long 09-05-2009 11:11 PM

Alright thanks, but I don't think my parents would want me using an actual solder, I burn't myself from carelessly using a coldheat solder. The good thing is RadioShack is 1 block away and Lowes is up the street. Would lowes have better soldering Irons? Cause I read the reviews on the RS ones and people say they stink.

bigez 09-05-2009 11:15 PM

well they might but i do not know try going to their web site if
they have one

TripleXmodder(akaXXX) 09-05-2009 11:33 PM

Quote:

Originally Posted by Michael Long (Post 236844)
Alright thanks, but I don't think my parents would want me using an actual solder, I burn't myself from carelessly using a coldheat solder. The good thing is RadioShack is 1 block away and Lowes is up the street. Would lowes have better soldering Irons? Cause I read the reviews on the RS ones and people say they stink.

RS soldering irons are fine. Its just a soldering pencil. You don't need to spend more then $10 on one. Just be sure to get one that is atleast 50volts, and gets to atleast 500degrees. I do lots of soldering and have 2 RS solders which I use all the time, and a $300 Weller soldering station.

Michael Long 09-06-2009 04:12 PM

Thanks for you help, but I waited one day and the car stopped glitching, but it's range is 1 inch. So then I put the car in the freezer now the range is in a drivable range.


All times are GMT -4. The time now is 08:12 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.