Originally Posted by xmodsNSX94 (Post 260581)

hey would there be much of a difference for you in the 1.9 or 2.2 class?
thanks
michael

Originally Posted by BulletsRain (Post 260582)

...and I believe they allow 4 wheel steering maybe.

Originally Posted by BulletsRain (Post 260582)

Thanks Donzi.
I was actually planning to maybe limit the articulation because it can cause it to roll.

Originally Posted by USRCCA Rules

2.3.1 - Vehicle wheelbase is limited to a maximum of 12.5 inches. This is determined by measuring
from centerline of front axle stub to centerline of rear axle stub, with all the wheels pointing straight
ahead, with the vehicles suspension holding it's own weight.
o 2.3.2 - Vehicle track width is limited to a maximum of 12.5 inches. This is determined by measuring
the bottom of the outer most edge of the front and rear tires while the vehicle is sitting on level ground.
o 2.3.3 - Vehicle is limited to 2.2 inch wheels/rims or smaller at the bead surface. Wheels may be modified provided
that the tire bead surface does not exceed 2.2 inches in diameter. With a tire mounted no exterior component of the
wheel including but not limited to the bead lock ring shall exceed 2.55". Tires may be modified from other sized tires
using only a pliable rubber but must not exceed a total uncompressed outer diameter of 6 inches.
o 2.3.4 - Vehicles are limited to 2-wheel steering only.
o 2.3.5 - 2.2 Crawler class bodiless 8" overall length, 3" overall width, and 3.75" overall height.
o 2.1.6 - Bodied vehicles must be 3” minimum height on sides. No less than 12.5”
total length and full original width, and no less than 5” in center.

Originally Posted by USRCCA Rules

2.4.1 - Vehicle wheelbase is limited to a maximum of 8.5 inches.
o 2.4.2 - Vehicle track width is limited to a maximum of 8 inches. This is determined by measuring the
bottom of the outer most edge of the front and rear tires while the vehicle is sitting on level ground.
o 2.4.3 - Vehicle is limited to 1.9 inch wheels/rims or smaller at the bead surface. Wheels may be modified provided
that the tire bead surface does not exceed 1.9 inches in diameter. With a tire mounted no exterior component of the
wheel including but not limited to the bead lock ring shall exceed 2.2". Tires may be modified from other sized tires
using only a pliable rubber but must not exceed a total uncompressed outer diameter of 4.25 inches.
o 2.4.4 - Vehicles are limited to 2-wheel steering on front axle only.
o 2.4.5 - Vehicles are limited to the use of 2 channels radio control (one for steering & one for throttle)
only. Neither channel can be used to perform more than one function. Radio systems with more than
2 channels are allowed but only 2 channels can be used to control the vehicle.
o 2.4.6 - Vehicles are limited to 1 ESC & 1 servo only.
o 2.4.7 - Vehicles are limited to 1 motor powering both of the axles.
o 2.4.8 – No driver controlled devices, other than steering and throttle control, will be allowed.
Independent throttle control to the front or rear axles (“burn” or “dig”), winching down the axles, and
forced articulation are not allowed in this class.
o 2.4.9 – A battery is limited to 11.1 nominal voltage.
o 2.4.10 – 1.9 Crawler class bodiless 6.75" overall length, 2.5" overall width, and 3.25" overall height.
o 2.4.11 - 1.9 Class body must be 2.75” minimum height on sides. No less than 9” total length and full original
width, and no less than 3” in the center. All bodies should resemble its original form (Jeep bodies look like a Jeep)

Originally Posted by USRCCA Rules

2.2.1 - Vehicle wheelbase is limited to a minimum of 16 inches and a maximum of 18 inches.
o 2.2.2 - No limits to steering configuration.
o 2.2.3 - Bodied vehicles must be 3” minimum height on sides. No less than 12.5” total length and full original
width, and no less than 5” in center.
o 2.2.4 - Super class bodiless 12" overall length, 3" overall width, and 3.75" overall height.
o 2.2.5 -Vehicle is limited to a minimum 3.2 inch wheels/rims or larger at the bead surface. Wheels may be
modified provided that the tire bead surface is not less than 3.2 inches in diameter. Tires may be modified from
other sized tires using only a pliable rubber.

Originally Posted by USRCCA Rules

2.5.1 - Vehicle wheelbase is limited to a maximum of 12.5 inches. This is determined by measuring
from centerline of front axle stub to centerline of rear axle stub, with all the wheels pointing straight
ahead, with the vehicles suspension holding it's own weight.
o 2.5.2 - Vehicle track width is limited to a maximum of 12.5 inches. This is determined by measuring
the bottom of the outer most edge of the front and rear tires while the vehicle is sitting on level ground.
o 2.5.3 - Vehicle is limited to 2.2 inch wheels/rims or smaller at the bead surface. Wheels may be modified,
provided that the tire bead surface does not exceed 2.2 inches in diameter. With a tire mounted, no exterior
component of the wheel, including but not limited to, the bead lock ring shall exceed 2.5". Tires may be modified
from other sized tires using only a pliable rubber, but must not exceed a total uncompressed outer diameter of 6
inches.
o 2.5.4 - Vehicles are limited to 2-wheel steering only.
o 2.5.5 - 2.2 Crawler class bodiless overall dimension of the complete chassis must be at least 8"overall length, 3"
overall width, and 3.75" overall height.
o 2.5.6 - Vehicles are limited to the use of 2 radio channels (one for steering & one for throttle) only. Neither
channel can be used to perform more than one function. Radio systems with more than 2 channels are allowed, but
only 2 channels may be used to control the vehicle.
o 2.5.7 - Vehicles are limited to 1 ESC & 1 servo only.
o 2.5.8 - (OPTIONAL) Vehicles are limited to 1 motor powering both of the axles.

Originally Posted by Donziikid (Post 260585)

Yupp, that's it! :)

Just out of curiosity, which club do you run with?

Cheers,
Kyle

Originally Posted by Stampedekid (Post 260614)

Looks very nice! I think you're just jealous of mine and Mycro's Honchos so you want a scaler too :p Just kidding looks pretty cool, but I'm happy with my micro scaler and the Honcho. I personally would tell you to stick to 1.9's but that's just my own personal likes. I find the 2.2 classes get more competitive and less for the fun of the hobby.

Originally Posted by dreamingISdrifting (Post 260697)

Integy isn;t all too bad, but still kinda bad... sure they give you a nice bling but they are prone to bending, Usually its because their parts break when put upon leverage...so if its thick and robust enough it should be fine, just my 2 cents

Originally Posted by dreamingISdrifting (Post 260724)

Isnt that what your suppose to do?? hehe ;)

Originally Posted by mycrors4 (Post 260645)

omg u ordered inte***! why.. why would u make the poor MRC suffer.. he never did anything to you! lol
im confused on the first order about the lockers.. oh well.. time to google

Originally Posted by BulletsRain (Post 260806)

Why are you confused about the lockers?

Originally Posted by mycrors4 (Post 261529)

niiiiiiiiice
the locked diffs will help a lot... trust me..

Originally Posted by Stampedekid (Post 261584)

With the bent links you'll notice a huge difference in what it can get over, and it won't get stuck as much. When the micro Scaler ran links out back after I bent them, there was a BIG difference in what it could and couldn't climb over.

Originally Posted by BulletsRain (Post 261617)

my right front wheel still likes to pop up in the air. Darn TT. :eyecraz: