lol
06-02-2010, 12:31 AM
Hai, I has a Legacy Rustler now.
Special Thanks to:
mycro: for advice
fuzzy: for the Rustler.
Time to get to the basics. Legacy Rustler. MSC. Brass bushings which are pretty impressive. Hard tires, no foam inserts. I took out MSC and replaced with XL-5. I burnt out my Titan 12T on my Slash, so I paired it up with the 20T Stinger. I also made a cut to battery slot to accommodate a 7cell Ni-Mh setup. I swapped out the 14AWG wires on the Stinger for 12AWG because I felt it needed better current flow. I made a rear chassis stiffener from the MSC mount and made a battery plate from the MSC Resistor mount My plans are:
1) Bearings for wheels as the transmission already has bearings.
2) Get another body. Body is too sexy to be driven
3) Bash and rash
I don't plan to race it unless it gets popular at the local track.
The outside.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2568.jpg
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2570.jpg
Here is my battery tray, I cleaned up the cuts after test run.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2567.jpg
Rear battery plate: with cleaned up cuts under.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2572.jpg
GUTS!
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2564.jpg
Tires all hard. Worn out rears already
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2562.jpg
After-run motor cooling method
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2561.jpg
Many Deans!
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2573.jpg
and a sneak peak at the Slash.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2569.jpg
Enjoy. :nod:
Special Thanks to:
mycro: for advice
fuzzy: for the Rustler.
Time to get to the basics. Legacy Rustler. MSC. Brass bushings which are pretty impressive. Hard tires, no foam inserts. I took out MSC and replaced with XL-5. I burnt out my Titan 12T on my Slash, so I paired it up with the 20T Stinger. I also made a cut to battery slot to accommodate a 7cell Ni-Mh setup. I swapped out the 14AWG wires on the Stinger for 12AWG because I felt it needed better current flow. I made a rear chassis stiffener from the MSC mount and made a battery plate from the MSC Resistor mount My plans are:
1) Bearings for wheels as the transmission already has bearings.
2) Get another body. Body is too sexy to be driven
3) Bash and rash
I don't plan to race it unless it gets popular at the local track.
The outside.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2568.jpg
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2570.jpg
Here is my battery tray, I cleaned up the cuts after test run.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2567.jpg
Rear battery plate: with cleaned up cuts under.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2572.jpg
GUTS!
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2564.jpg
Tires all hard. Worn out rears already
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2562.jpg
After-run motor cooling method
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2561.jpg
Many Deans!
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2573.jpg
and a sneak peak at the Slash.
http://i116.photobucket.com/albums/o29/aznkevin4eva/101_2569.jpg
Enjoy. :nod: