GearHeadV8
07-31-2008, 06:28 PM
What you will need:
1.1 truck shock top and bottom
2.exacto knife
3.ball joint
4.drill
Step 1
Get a drill bit and drill out the small square on the back of the hummer Bumper
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1545.jpg
Step 2 get the shock
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1546.jpg
Step 3
Bend the male piece of the shock up like this.(you will needto trim it later on)
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1548copy.jpg
Step 4
Trim the female down alittle bit
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1550.jpg
Step 5
If you are using a ball that has a small screw piece you will need to trim it down abit.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1551copy.jpg
Step 6
Trim down the male piece so it will fit nicely in it.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1548copy.jpg
Step 7
Then take the female piece and screw it on the back of the bumper.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1556.jpg
Step 8
Now put in your ball hitch on.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1554.jpg
Step 8
Slide in the male to the female if you want put some glue in for a permanant or none for a removable hitch.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1557.jpg
Step 8
Now i am using a model trailer.make a small hole in the front of the hitch and put a ball adapter on.You will need to put a screw in the adapter then glue it in and cut off the flat head on the screw and screw it in the hole you made on the trailer.then glue.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1559.jpg
There you are a small drop hitch that is very easy to use
COMMENTS ARE WELCOME PLEASE
1.1 truck shock top and bottom
2.exacto knife
3.ball joint
4.drill
Step 1
Get a drill bit and drill out the small square on the back of the hummer Bumper
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1545.jpg
Step 2 get the shock
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1546.jpg
Step 3
Bend the male piece of the shock up like this.(you will needto trim it later on)
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1548copy.jpg
Step 4
Trim the female down alittle bit
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1550.jpg
Step 5
If you are using a ball that has a small screw piece you will need to trim it down abit.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1551copy.jpg
Step 6
Trim down the male piece so it will fit nicely in it.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1548copy.jpg
Step 7
Then take the female piece and screw it on the back of the bumper.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1556.jpg
Step 8
Now put in your ball hitch on.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1554.jpg
Step 8
Slide in the male to the female if you want put some glue in for a permanant or none for a removable hitch.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1557.jpg
Step 8
Now i am using a model trailer.make a small hole in the front of the hitch and put a ball adapter on.You will need to put a screw in the adapter then glue it in and cut off the flat head on the screw and screw it in the hole you made on the trailer.then glue.
http://i253.photobucket.com/albums/hh69/crazyxmoder/IMG_1559.jpg
There you are a small drop hitch that is very easy to use
COMMENTS ARE WELCOME PLEASE