BL micro-t Question

[bestdragon2001]

If I use this reciever in a BL Micr-t will I still be able to use the original controller?
http://www.atomicmods.com/Products/SM1001-DSM-Pro-Series-Module-For-KO-Propo-or-JR-Radio-Systems__12935.aspx

[2wdpancar]

Which receiver.....?
You have to buy an aftermarket TX and receiver dude.
I am getting the Futaba LP2 pack, TX and receiver...
Very small.

[c1v1c]

Yes like blt said, Its a whole different concept. then the stock micro-t electronic.

[bestdragon2001]

Sorry I had forgot the link. Could I use a KO Propo Mini-z TX?

[2wdpancar]

Sorry I had forgot the link. Could I use a KO Propo Mini-z TX?

Erm if you find a small enough receiver it should work....
My receiver is pretty **** big:lol:

[bestdragon2001]

Ok well the one in the first post can work with KO Propo radios
How much is it going to cost you to do the whole thing.

[2wdpancar]

Depends what you buy.
I bought the 10250Kv motor, esc, JR receiver.
I had a TX, but it's costed me around 150 so far.......

[bestdragon2001]

Well I think brushless woulbe too much for me so what if i get bearings, bb motor and liths what kind of speed would it have?
Also do they make any other better upgrades than them, like different motors and battery packs?

[c1v1c]

Get a handwound motor from either blt or redsxmodder, get an external turbo v2/nelly/spyder and liths, bearings and gpm parts...U'll get around 30mph.

[2wdpancar]

MhHmmm.....
Well, re-winding the N20 motors, Ill leave that to RED, I cracked a stocker open, **** it was small:lol:

Yeah, but these have been covered in other locations, getting a bit sick of repeating myself...

Make your own battery pack.
Wire a S2 LiPo pack...

[bestdragon2001]

How do you install the spider?

[2wdpancar]

How do you install the spider?

The spider, you have to remove the stock fets...........
PH2T put a nelly on his, I bet it's the same for a V3...
http://www.ausmicro.com/forum/showthread.php?t=14442
You're welcome.

[bestdragon2001]

Thanks Im definately going to get a nelly

[xmodificationer]

Get a handwound motor from either blt or redsxmodder, get an external turbo v2/nelly/spyder and liths, bearings and gpm parts...U'll get around 30mph.

where are you getting this info from?

Lipo's and a Atomic BB motor will get you 30 mph in a micro-t. I would know, i have both.

[c1v1c]

Uh?

[bestdragon2001]

Well if I could go 30 mph with the bb motor and liths I should be able to go way faster with the nelly and stuff right?

[xmodificationer]

this is for a micro-t right?

[bestdragon2001]

this is for a micro-t right?
yes

[c1v1c]

Oh my bad tought it was for xmods sorry bro.

[xmodificationer]

ok, i was like what is civic saying lol. But yea There is really no point in going BL in a micro-t unless you have the money, or just want a fast RC car that runs for about 3 minutes. Seriously, save your money and just get Lipo, BB motor, Bearings, and maybe some gpm. But thats about it. Going BL wont make it a ton faster, and you will get alot shorter run times. Besides around 30-35mph is plenty fast for a car of this side. Argue with this and you will lose. I know my micro-t's.

[bestdragon2001]

Hey could you post pics of your micro-ts
Im going to get a nelly and a motor from redsxmoder

[RedSXmodder]

MhHmmm.....
Well, re-winding the N20 motors, Ill leave that to RED, I cracked a stocker open, **** it was small:lol:


Already done. Waiting on Donzii to get some pics for me. 16t of pure maddness :p

Later,
RedSXmodder

[xmodificationer]

http://i179.photobucket.com/albums/w285/carcrazycorey/Picture201.jpg
http://i179.photobucket.com/albums/w285/carcrazycorey/Picture200.jpg
http://i179.photobucket.com/albums/w285/carcrazycorey/Picture169.jpg
http://i179.photobucket.com/albums/w285/carcrazycorey/Picture172.jpg
http://i179.photobucket.com/albums/w285/carcrazycorey/Picture171.jpg
http://i179.photobucket.com/albums/w285/carcrazycorey/Picture158.jpg

I have around $160 in it.

[c1v1c]

ok, i was like what is civic saying lol. But yea There is really no point in going BL in a micro-t unless you have the money, or just want a fast RC car that runs for about 3 minutes. Seriously, save your money and just get Lipo, BB motor, Bearings, and maybe some gpm. But thats about it. Going BL wont make it a ton faster, and you will get alot shorter run times. Besides around 30-35mph is plenty fast for a car of this side. Argue with this and you will lose. I know my micro-t's.

You've seen bl micro-t run already???

[xmodificationer]

um yea:lol:

[RedSXmodder]

BL is pretty insane, but the motors tiny. There's a guy on MZM putting it into a Mini-Z LIT (insanity?)...

But, if I'd put my 16t arm into a BB can, pair it with a Nelly, I can guarantee it'll be faster then brushless (unless of course your stuff a Mamba or Fieago into it)

Later,
RedSXmodder

[xmodificationer]

Before Losi released their BL, some people used Fieago. here is a BL micro-t on dyno. http://www.youtube.com/watch?v=i_dF0LU4Weg&feature=related

[c1v1c]

AWww man...i tought it would of been better...you popped my bubble eheh:P

[xmodificationer]

[YOUTUBE]http://www.youtube.com/watch?v=v_99JGGuvuk&feature=related/YOUTUBE]

here is a BB motor and Lipo going the same speed:lol: BL really isnt worth it.

[bestdragon2001]

Ok guys Im getting a custom motor from Redsxmodder and I will buy a nelly and a lipo, I should have everything together by march!
Is installing the nelly an a micro-t just like it is on the evo?

[2wdpancar]

Haha red that's cool man:)
Is it crazy?
I bet so..?
What awg you use, probably 31/32?

BTW, you can't get nellies anymore.
Good luck finding one, and no it isn't the same install.
I posted a link, that's how ph2t installed his nelly...

[bestdragon2001]

It dosent tell how he did it does it?

[2wdpancar]

It dosent tell how he did it does it?

It shows a pic.
I can't hand-feed you info, you gotta search dude.:cool: